A garage door should receive a tune-up at least once a year, and although that seems like a difficult task it becomes easier as long as you follow these simple steps.

Look for Problem Spots
The first step in your garage door tune-up is to look for any obvious problem spots in your garage door system. Rollers should be in working order, the seal around the door should be pliable and the door itself should not be dented or warped. Any parts that are overly worn or damaged should be replaced.

It is also important to disconnect the power to the garage door opener before looking over your garage door system. The last thing you want is to have your garage door to open while you’re working.

Lubricate the Roller
If you have metal rollers, they can be easily lubricated with WD-40. If you have vinyl or rubber rollers, you will have to use another lubricant since WD-40 can damage non-metal components.

Re-Align Locking Bars
Misaligned locking bars are common and can prevent the garage door from sliding into the slots on the door track and locking into place. If the locking bars are misaligned, loosen the screws on the guide brackets that hold the locking bars in place and tap them gently into place with a hammer until they are aligned with the slots. Tighten the screws when you’re finished.

Inspect and Clean Moving Parts
Your garage door has several moving parts, which is why it is subject to so much wear and tear. Loose bolts and screws will all need to be tightened, and any gummy parts will need to be removed and soaked in mineral spirits. To make sure all parts that are removed are put back in the right place, try to only remove one part at a time.

Lubricate Chains and Springs
The chains of a garage door system can be lubricated with white lithium grease, while the springs will require a silicone-based spray. The springs are under a lot of tension and can pose a safety hazard, so don’t be afraid to contact a professional to inspect or replace them safely.

For more information on garage door repairs or any of your garage door repairs, please follow us on Facebook or Twitter or feel free to contact us!

The post Garage Door Tune Up Billings MT appeared first on Bailey Garage Doors Belgrade MT.

A Garage Door’s spring is a mechanical component to the garage door, and because of the pressures placed upon it to both raise and lower the door, the springs will eventually go bad. The problem with garage door springs is that it’s not the easiest component to fix. As we’ve talked about here before, because of the pressures behind those springs, for the amateur, or even professional for that matter, those springs can represent serious bodily pain, loss of limb or maybe even life. It’s best to call a professional if you don’t have either the knowledge or practice replacing these springs.

When a spring does break, it could be at the worst possible time—when you are hoping to leave for work, school, etc. You will know a spring has broken when the garage door wont open or close—this could also be a sign of other problems such as a faulty garage door opener, etc., and the list of ways in which to troubleshoot a stuck garage door can be found in February’s blog post. If you’ve determined that the spring is at fault, call a professional technician at Bailey’s Garage Door. If you continue to try and engage the spring by continuing to try to open and close the garage door, it could do severe damage to the door.

So, how do you prevent this moment in time in which you’re stuck with a broken garage door, hoping that a Garage Door Technician is available soon! There may have been warning signs before the door became stuck, warning signs that you could have caught early, and avoided the stuck disaster. Unfortunately, however, garage door springs wont break in standard ways, but often it might provide clues as to its wear. Firstly, if your garage door is stopping as it’s opening or closing this could be a sign of a damaged spring. Check the springs when the door is fully closed, and look for any noticeable damage or wear to the spring. Another clue is how the door is situated in the opening. Is the door crooked? Does it seem to be off its track? These could be definite clues that point to a faulty spring. Also, there’s the standard practice of if it looks broke then fix it! If there’s noticeable wear, or if you’ve had a simple accident such as backing into the door, or clipping the door with your car as you passed underneath, this would be a definite time to have the springs checked, and, possibly, replaced. You don’t want to find yourself with your car stuck in or just outside the garage at a time of emergency.

For all of your garage doors needs, please contact Bailey Doors today!

The post Garage Door Springs Billings MT appeared first on Bailey Garage Doors Belgrade MT.

The springs are still dangerous for a professional garage door technician to replace. When a technician replaces the broken springs, he has to assume that the tension springs will break when he unwinds them. He will need to wear a set of safety glasses and keep his clothes and body parts well away from the springs. A component of the garage door called the winding cone keeps the tension spring in place. These cones can slip or even explode into many pieces and great care should be taken to prevent possible injury.

Extension springs, are built differently then tension springs, because these springs are held into place by safety cables. These cables help to control the broken spring, but even though it is in place for a safety precaution, the springs are still held up under a tremendous amount of pressure and a professional technician should probably be called in the event that one breaks.

Diagnosing a garage door spring problem is simple: does the door open and close smoothly? If the door is not operating smoothly, it is likely the tension springs. If the door is making noise, turn off the garage door opener and try open the garage door manually. If the garage door still makes noise the problem is likely the springs. It is also possible that a noisy garage door may just need some lubricant to be applied to the springs. The average home can easily diagnose and fix these simple problems with a garage doors springs, but even the most seasoned DIY’er should probably allow a garage door technician to fix the garage door spring when it breaks..

The post Garage Door Springs appeared first on Bailey Garage Doors Belgrade MT.

Like any major appliance in the home the garage door and the garage door opener should be regularly maintained to prevent poor service or possible failure. To begin maintenance, tell everyone in the home your plan to work on the garage door or opener to prevent any possible injury. The first step to garage door maintenance is simple: stand inside the garage with the garage door closed; inspect the springs, rollers, pulleys and all of the mounting hardware for both the garage door and the opener. If there are any signs of damage or noticeable wear to these components, it may be time to call your garage door professional to replace the damaged or worn components (Remember garage doors are held up under a lot of tension, and a trained professional should be called to replace damaged hardware to prevent any possible injury to the homeowner).

The balance of the garage door should also be regularly checked to ensure the garage door is opening and closing with no resistance along its track. With the garage door closed, disconnect the automatic door opener, and, with the automatic door opener disconnected, lift the garage door manually into an open position. If the door moves smoothly and freely into the upward position, the door is in alignment. If, however, the door catches and drags on the rails, a trained garage door technician should properly service the door.

The garage door’s reversing mechanism – devices which have been added to all garage doors built after 1993 and are responsible for the prevention of the possible entrapment of a person under the garage door – should also be tested regularly. To test the door’s reversing mechanism, open the garage door and place a two by four on the garage floor directly in the path of the garage door. With the two by four in place, close the garage door onto it. When the garage door falls on the two by four and makes contact, the garage door should retreat back up on the track into the open position. If the door does not immediately retract, call your garage door service technician to fix the reversing mechanism.

On a final note, a small amount of lubrication can be added to all of the garage doors moving parts. Make sure that the garage door is either in a fully opened or closed position while working on the garage door, and stand clear of the garage door and all of the moving parts when the garage door is activated.

The post Garage Door Opener Maintenance appeared first on Bailey Garage Doors Belgrade MT.